for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 96 hmc713ms8 / 713ms8e general description features functional diagram the hmc713ms8(e) logarithmic detector/control- ler is ideal for converting rf signals with frequencies in the 100 mhz to 2700 mhz range, to a proportional dc voltage at its output. the hmc713ms8(e) employs a successive compression technology which delivers 54 db of dynamic range with high conversion accuracy over a wide input frequency range. as the input signal is increased, successive ampli ers move into satura- tion one by one creating an accurate approximation of the logarithm function. the outputs of a series of detectors are summed, converted into voltage domain and buffered to drive the out output. for detection mode, the out pin is connected to the vset input and will provide a nominal logarithmic slope of 17 mv/db and an intercept of -68 dbm. the hmc713ms8(e) can also be used in the controller mode where an external voltage is applied to the vset pin to create an agc or apc feedback loop. wide dynamic range: up to 54 db high accuracy: 1 db with 54 db range up to 2.7 ghz fast output response time supply voltage: +2.7 to +5.5v power-down mode excellent stability over temperature msop-8 smt package: 14.8 mm2 typical applications the hmc713ms8(e) is ideal for: ? cellular infrastructure ? wimax, wibro & lte/4g ? power monitoring & control circuitry ? receiver signal strength indication (rssi) ? automatic gain & power control ? military, ecm & radar electrical speci cations, t a = +25c, vcc= +3v [1] 54 db, logarithmic detector / controller, 100 - 2700 mhz v00.1008 parameter typ. typ. typ. typ. typ. units input frequency 100 900 1900 2200 2700 mhz 3 db dynamic range 61 61 62 62 68 db 3 db dynamic range center -28 -28 -30 -31 -27 dbm 1 db dynamic range 54 54 54 53 59 db o u t s l o p e 17. 3 17. 2 17.1 17.1 17. 2 mv/d b out intercept -68 -69 -71 -72 -70 dbm variation of out with temperature from -40c to +85c @ -20 dbm input -1 -0.9 -0.5 -0.6 -0.5 db [1] detector mode measurements; out (pin 6) is shorted to vset (pin 3) through an rc network.
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 97 electrical speci cations, (continued) hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz parameter conditions min. typ. max. units power down (en) interface voltage range for normal mode 0 0.2 x vcc v voltage range for powerdown mode 0.8 x vcc vcc v threshold voltage vcc/2 v power supply (vcc) operating voltage range 2.7 - 5.5 v supply current in normal mode 17 ma supply current in power down mode 0.3 ma out interface rise time clpf= 0, no power to -10 dbm, 10% - 90% 24 ns fall time clpf= 0, -10 dbm to no power, 90% - 10% 70 ns output video bw 3 db reduction in demodulated output voltage 16 mhz voltage range closed loop (eval board setup) 0.2 - 1.2 v voltage range open loop 0.1 to (vcc -0.1) v current drive source / sink 3.5 / 0.51 ma outn interface current drive source / sink 3.6 / 0.47 ma outn interface output voltage range 0.2 - 2.1 v rf input input return loss (s11) f= 50 mhz to 2.5 ghz z 0 = 50, see plot 10 db vset interface input impedance 1m input voltage range eval board 0.2 - 1.2 v low frequency gain vset to out 64 db open loop corner frequency 11 k hz
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 98 output voltage & error vs. input power, fin = 2700 mhz output voltage & error vs. input power, fin = 2200 mhz output voltage & error vs. input power, fin = 1900 mhz unless otherwise noted: vcc= +3v, t a = +25c hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz 0 0.4 0.8 1.2 1.6 2 2.4 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 out err +25c out err +85c out err -40c out n err +25c out n err +85c out n err -40c out, outn (v) error (db) input power (dbm) out out n 0 0.4 0.8 1.2 1.6 2 2.4 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 out err +25c out err +85c out err -40c out n err +25c out n err +85c out n err -40c out, outn (v) error (db) nput power (dbm) out out n 0 0.4 0.8 1.2 1.6 2 2.4 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 out err +25c out err +85c out err -40c out n err +25c out n err +85c out n err -40c out, outn (v) error (db) input power (dbm) out out n input return loss -50 -40 -30 -20 -10 0 0 0.5 1 1.5 2 2.5 3 frequency (ghz) return loss (db) output voltage & error vs. input power, fin = 900 mhz output voltage & error vs. input power, fin = 100 mhz 0 0.4 0.8 1.2 1.6 2 2.4 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 out err +25c out err +85c out err -40c out n err +25c out n err +85c out n err -40c out, outn (v) error (db) input power ( dbm ) out out n 0 0.4 0.8 1.2 1.6 2 2.4 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 out err +25c out err +85c out err -40c out n err +25c out n err +85c out n err -40c out, outn (v) error (db) in p ut power ( dbm ) out out n
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 99 unless otherwise noted: vcc= +3v, t a = +25c out slope vs. frequency out slope vs. supply voltage hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz 14 15 16 17 18 19 20 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 +25c +85c -40c frequency (ghz) slope (mv/db) 15 16 17 18 19 20 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 0.1ghz 0.9ghz 1.9ghz 2.2ghz 2.7ghz slope (mv/db) voltage supply (v) out vs. frequency & input power out voltage & error vs. frequency out intercept vs. supply voltage out intercept vs. frequency 0 0.3 0.6 0.9 1.2 1.5 1.8 -6 -4 -2 0 2 4 6 -60 -50 -40 -30 -20 -10 0 10 0.1ghz 0.9ghz 1.9ghz 2.2ghz 2.7ghz out (v) error (db) input power (dbm) out error 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 frequency (ghz) out (v) 0dbm -10dbm -20dbm -30dbm -40dbm -50dbm -60dbm -100 -90 -80 -70 -60 -50 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 +25c +85c -40c frequency (ghz) intercept (dbm) -100 -90 -80 -70 -60 -50 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 0.1ghz 0.9ghz 1.9ghz 2.2ghz 2.7ghz intercept (dbm) voltage supply (v)
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 100 output response rise time @ 900 mhz, c1 = open output response rise time @ 900 mhz, c1 = 10nf hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz 0 0.3 0.6 0.9 1.2 1.5 0 50 100 150 200 250 300 350 400 450 500 0dbm -10dbm -20dbm -30dbm time (ns) out (v) 0 0.3 0.6 0.9 1.2 1.5 0 102030405060708090100 0dbm -10dbm -20dbm -30dbm time (us) out (v) unless otherwise noted: vcc= +3v, t a = +25c output response fall time @ 900 mhz, c1 = open output response fall time @ 900 mhz, c1 = 10nf 0 0.3 0.6 0.9 1.2 1.5 0 50 100 150 200 250 300 350 400 450 500 0dbm -10dbm -20dbm -30dbm time (ns) out (v) 0 0.3 0.6 0.9 1.2 1.5 0 25 50 75 100 125 150 175 200 0dbm -10dbm -20dbm -30dbm time (us) out (v)
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 101 absolute maximum ratings vcc 0 to +5.6v en 0 to +5.6v vset 0 to +5.6v out output current 5 ma outn output current 5 ma rf input power 12 dbm junction temperature 125 c continuous pdiss (t = 85c) (derate 5.43 mw/c above 85c) 0.22 watts thermal resistance (r th ) (junction to lead) 184 c/w storage temperature -65 to +150 c operating temperature -40 to +85 c electrostatic sensitive device observe handling precautions package information outline drawing part number package body material lead finish msl rating package marking [3] hmc713ms8 low stress injection molded plastic sn/pb solder msl1 [1] h713 xxxx HMC713MS8E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h713 xxxx [1] max peak re ow temperature of 235 c [2] max peak re ow temperature of 260 c [3] 4-digit lot number xxxx hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz notes: 1. package body material: low stress injection molded plastic silica and silicon impregnated. 2. lead material: copper alloy 3. lead plating: 100% matte tin 4. dimensions are in inches [millimeters]. 5. dimension does not include moldflash of 0.15mm per side. 6. dimension does not include moldflash of 0.25mm per side. 7. all ground leads must be soldered to pcb rf ground.
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 102 pin number function description interface schematic 1 inp rf input pin. 2en enable pin. apply ven >0.8 x vcc for normal operation. apply ven <0.2 x vcc to disable the part. 3vset setpoint input for controller mode. connect to out with the resistor network shown in evaluation board drawing for detector mode. 4clpf connection for ground referenced external lowpass lter capacitor. 5gnd device ground. pin descriptions hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 103 pin number function description interface schematic 6out logarithmic output that converts the input power to a dc level in controller mode. output voltage increases with increasing amplitude 7outn inverted logarithmic output. outn= 2.55 - 2 x out 8vcc bias supply. connect supply voltage to all this pin with appropriate ltering. pin descriptions (continued) hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 104 application & evaluation pcb schematic notes note 1: the hmc713ms8(e) evaluation board is pre-assembled for single-ended input, and detector/rssi mode. note 2: for detector mode, connect high impedance volt meter to the out / outn port, and make no connection to vset. note 3: for controller mode, remove r6 & c3 and install 1k resistor (r4), then make appropriate connection to out and vset. in controller mode, the out / outn output can be used to drive a variable gain ampli er, or a variable attenuator, either directly or through a buffer or microcontroller. vset should be connected to an external supply, typically between +0.2 and +1.2v. note 4: an external capacitance c1 can be connected to clpf port for additional ltering of out and outn outputs.. hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com power detectors - smt 12 12 - 105 item description j1 - j4 pc mount sma connector j5 - j7 dc pin c3 1 pf capacitor, 0402 pkg. c6 0.1 f capacitor, 0402 pkg. r1, r7, r10 0 resistor, 0402 pkg. r2 51 resistor, 0402 pkg. r3, r5 10k resistor, 0402 pkg. r6 1k resistor, 0402 pkg. u1 hmc713ms8(e) logarithmic detector / controller pcb [2] 121944 evaluation pcb [1] reference this number when ordering complete evaluation pcb [2] circuit board material: arlon 25fr or rogers 4350 evaluation pcb the circuit board used in the nal application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be con- nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from hittite upon request. list of materials for evaluation pcb 121947 [1] hmc713ms8 / 713ms8e v00.1008 54 db, logarithmic detector / controller, 100 - 2700 mhz
|
